Free estimates from a family-owned electrical contractor. License EC13013906.

Call (727) 258-3346
Call Now
Get a Free Estimate
Free Estimate

Wiring you can trust

Home Electrical Rewiring for Older and Growing Homes

Home electrical rewiring replaces tired, damaged or undersized wire with new copper circuits built for how you live now. We plan it room by room, keep the mess small and leave you with a home that passes inspection.

5.0 on Google, 100+ reviews
License EC13013906
Family-owned and operated
Free estimates

Free estimate

Tell us what you need

Finished workshop interior with new wiring overhead and a roll up door at the far end

5.0

Stars from 116 Google reviews (September 2026)

Licensed

Florida Certified Electrical Contractor, License EC13013906, on record with the state DBPR

5

Counties served: Sarasota, Manatee, Hillsborough, Polk and Pinellas

15

Electrical services, from panel upgrades to smart homes, one family team

Drawing of home electrical rewiring: new cable runs pulled through open wall studs

Why worn wiring is more than an annoyance

Wire hides in the walls, so it is easy to forget until something goes wrong. Lights flicker, a breaker trips every time the microwave runs, or an outlet feels warm to the touch. Those are more than small annoyances. They can be early signs of a connection that is failing.

Florida is hard on wiring. Attic heat bakes insulation for months at a time. Salt air near the Gulf eats at connections. Storm surges and lightning stress the whole system, and rodents in the attic chew what they can reach.

Home electrical rewiring fixes the problem at its root. New circuits, sized for today’s loads and protected to current code, make the house safer and quieter. You also gain room for the things a family now runs every day, from a second fridge to an EV charger.

6 warning signs your home needs rewiring

Faulty wiring does not always announce itself, but these signs are worth a call. Any one of them is reason to have a licensed electrician look.

  • Breakers that trip often, especially on circuits that used to be fine.
  • Lights that flicker or dim when the air conditioning or a big appliance starts.
  • Warm, discolored or buzzing outlets and switches, or a faint burning smell.
  • Two-prong outlets throughout the house, a clue that the wiring has no ground.
  • Aluminum branch wiring or cloth-covered wire seen in the attic or at the panel.
  • A failed or flagged inspection, such as an insurance four point report or a buyer’s home inspection.

Seeing one of these signs? Have it checked

We find the cause first and tell you plainly whether you need a repair, a partial rewire or a full one. The estimate is free.

What counts as outdated wiring?

Several kinds of wire show up in older Florida homes. Single-strand aluminum branch wiring was used in many houses built in the 1960s and 1970s. Aluminum expands and contracts more than copper, so its connections can loosen and heat up over years.

Cloth-insulated wire from the 1950s and earlier dries out and cracks. Knob and tube wiring, rare here but found in some of the oldest homes, has no ground and was never meant to sit under modern attic insulation.

Even newer copper wire can be outdated when the house has grown around it. An addition fed from an old circuit, a garage workshop on a single outlet, or a kitchen with too few circuits for its appliances all call for new runs. Age matters less than condition and load.

Financing

Pay for the Job Over Time

Financing available through Synchrony, subject to credit approval. Ask us about financing options when you call or book your free estimate.

  1. Free written estimateYou know what the job costs before you apply for anything.
  2. Ask when you bookTell us you want to finance and we walk you through the application.
  3. Terms before you signSynchrony shows you the plan terms, and you decide from there.

Financing through Synchrony

Aluminum wiring replacement and repair options

If your home has aluminum branch wiring, there are two sound paths. The first is to rewire with copper, which removes the problem for good. The second, when a full rewire is not practical, is to repair each connection with a connector listed for joining aluminum to copper.

What we do not do is wrap wires in tape and call it fixed, or use standard twist connectors meant for copper only. Those shortcuts are how aluminum connections fail.

Insurers in Florida often ask about aluminum wiring on a four point report. We can inspect your system, document what is there and tell you which path fits your house and your plans for it.

Found aluminum wire in the attic? Talk to us

Send a photo of the wire markings or the panel. We will tell you what it is and what your choices are.

What should you do about knob and tube wiring?

Knob and tube wiring is the oldest system you may find, with single wires run on porcelain knobs and through porcelain tubes in the framing. It is rare in Florida but turns up in some early homes and older additions. It has no ground, its insulation is often brittle, and it was designed to shed heat into open air, not to sit under insulation.

Many insurers will not cover a home that still runs on it. The fix is home electrical rewiring of those circuits with modern copper cable, done in sections while the old runs are disconnected and left safe. If you are not sure what is in your attic, an electrical inspection will tell you before you plan the rewiring.

How home electrical rewiring works, room by room

A rewire is a planned project, not a demolition. This is the order we follow.

  1. 1

    Inspect and map the circuits

    We trace every circuit from the panel, test the wire and connections, and note what the rooms need now.

  2. 2

    Plan the new runs

    We lay out the new circuits and the route for each, using the attic and existing openings to keep holes to a minimum.

  3. 3

    Pull the permit

    Rewiring changes your electrical system, so it goes through your city or county building department before work begins.

  4. 4

    Rewire in phases

    We work a section at a time so most of the house keeps power, and we close up small access holes as we go.

  5. 5

    Test, label and inspect

    Every circuit is tested and labeled at the panel, then we meet the inspector for the rough and final inspections.

Panel swap in progress with the old circuits pulled free before they are landed on new breakers

Can you rewire a house without removing walls?

In most homes, yes. We fish new wire through the attic and down inside the walls, cutting small access holes only where a run cannot be pulled any other way. Those openings are neat and easy to patch.

Block homes are more common here than in many states. Concrete block walls leave less room to fish wire, so some runs go through the attic and drop down in a chase or a surface raceway. We show you where every route will go before we start.

If you are planning a remodel anyway, open walls make whole house rewiring faster and simpler. Talk to us before the drywall goes back up.

GFCI and AFCI protection come with new circuits

New wiring means current protection. GFCI devices guard against shock where water is near, in kitchens, bathrooms, garages, laundry areas and outdoors. The moment current strays toward ground, they cut the power faster than you can blink.

AFCI breakers watch for the arcing that can start a fire inside a wall. Current code calls for them on the living-space circuits of a home, such as bedrooms, living rooms and hallways.

When we rewire, we add both kinds of protection where the code calls for them. Our page on electrical code corrections explains the rules in more detail, including what an inspector looks for.

Plan the rewiring once, for the long run

Copper circuits, the right protection and clear labels at the panel. Ask us to plan it with you, free.

When rewiring shows the panel needs work too

A rewire often exposes an old panel that cannot carry the new circuits. It may be full, rusty, or a brand with a poor track record. Replacing it during the same project saves a second permit and a second visit.

We look at the panel on the first visit and tell you whether it can stay. If it cannot, panel replacement becomes part of the plan, with surge protection added where the code calls for it.

If you only want to know where things stand, an electrical inspection gives you a written picture of the whole system before you decide anything.

Partial rewiring or a whole house rewire

Not every home needs every wire replaced. Sometimes the problem is one addition, one room or one old circuit that feeds too much. A partial rewire fixes that section and leaves sound wiring alone.

Whole house rewiring makes sense when the wire itself is the issue: aluminum branch circuits, brittle cloth insulation or damage spread across the attic. It also makes sense before a big remodel or when you plan to stay in the home for many years.

We tell you which one your house needs, and why, with photos from the inspection.

Google reviews

A Sarasota home that needed a full upgrade

Rated 5.0 on Google from more than 100 reviews. A few of them, word for word.

My wife and I purchased a second home in Sarasota that was in desperate need of a total electrical upgrade. We reached out to several other local companies and were given multiple estimates.

Phil

Google review

New panel on a garage block wall with its wiring run straight up into the ceiling

Rewiring for sheds, workshops and additions

Plenty of our wiring jobs are not old houses at all. They are workshops and sheds that need real power for tools, lights and an air conditioner, or additions that were tacked onto an existing circuit.

For a detached building, we run a feeder underground in conduit to a small subpanel, then wire outlets and lighting inside. Our own job photos show a trench to a shed, the subpanel on the wall and new cable runs along the rafters.

The same care goes into each one: the right wire size, a proper ground and GFCI protection where the code wants it.

Power a shed, workshop or addition

Tell us what you plan to run out there and how far it sits from the house. We will size the feeder and quote it free.

Rewiring, home insurance and resale

Florida insurers look hard at older electrical systems. A four point inspection report lists the panel, the wiring type and any hazards the inspector saw. Aluminum branch wiring, cloth insulation, double taps and missing covers can all lead to questions, a higher premium or a request for repairs before a policy is written.

Home electrical rewiring clears those items with a permit and a final inspection behind it. That paper trail helps when you renew, when you switch carriers and when you sell.

Buyers notice too. A home inspector who finds updated circuits, labeled breakers and current protection has less to write up, and that keeps a sale moving instead of stalling over repair credits. If you plan to sell in the next few years, rewiring before you list is often easier than negotiating it later.

Home electrical rewiring for the way you live now

Houses built decades ago were wired for a few lamps, a fridge and a window unit. Today the same house runs central air, a second fridge in the garage, a home office, a big TV, a pool pump and maybe an electric car. Old circuits were never sized for that load.

Part of home electrical rewiring is adding what the house is missing. That means dedicated kitchen circuits so the toaster and microwave can run together, and a separate circuit for the home office. It also means outdoor outlets where you use them and a 240 volt circuit ready for an EV charger.

We ask how you use each room before we plan. The goal is a home where you never have to think about which outlets you can use at the same time.

Tell us what your home needs to run

New kitchen, home office, pool or EV on the way? We plan the new circuits with the rewire so it is done once.

What we look for in the attic and at the panel

The attic tells the story of a home’s wiring. We look for splices that sit loose instead of inside a junction box, wire that has been chewed, insulation that has turned brittle in the heat and old runs buried under newer insulation.

At the panel we check the wire markings, the breaker brands, signs of heat on the bus and whether two wires share one breaker screw. We also measure the voltage under load to find weak connections.

You get what we find in plain words, with photos, before any rewiring plan is written.

Permits and code for rewiring in Florida

Every rewiring project has to meet the Florida Building Code, which adopts the National Electrical Code for its electrical rules. The code requires a permit to alter or replace a home’s wiring, and it offers no exemption for this kind of job. You can read the electrical chapter on the ICC’s Florida Building Code site.

The state’s newer permit break for small single-family projects leaves electrical work out, so it does not apply. Our office handles the filing, and the inspector sees the work at rough-in, before walls are closed, and again at the end.

A permitted, inspected rewire is also what buyers and insurers want to see. Keep the closed permit with your home records.

Home electrical rewiring near you

We rewire homes across Sarasota, Manatee, Hillsborough, Pinellas and Polk counties, from Parrish, Bradenton and Palmetto to Sarasota, Venice, Sun City Center and St. Petersburg.

Venice has many homes from the 1960s through the 1980s. Our guide to electrical rewiring near you in Venice covers that town in detail, and our electrician in Venice page lists everything else we do there.

Bluefin Power Solutions is a Florida Certified Electrical Contractor, License EC13013906. Check it on the state DBPR record.

Book your rewiring estimate

Our office is open Monday to Friday, 8 AM to 6 PM. Call, or send the form and tell us the age of the house and what you have noticed.

Questions

Home electrical rewiring questions

Often, yes, but age alone does not decide it. We test the wire, the connections and the load. Sound copper from that era may only need a few new circuits. Aluminum branch wire, brittle insulation or a house that trips breakers daily usually earns a fuller job.

It depends on the size of the home, its construction and how much wire is being replaced. A partial job may take a day or two. A full rewire takes longer, done in phases so you can live in the house while we work. Your estimate gives a realistic schedule.

In most cases, yes. We work in sections so the rest of the house keeps power, and we tell you each day which rooms will be off and for how long. Plan to move fragile items away from the walls we are working on.

Worn wiring keeps getting worse. Loose connections heat up, breakers trip more often, and the risk of a fire inside a wall grows. You may also have trouble with insurance or with a buyer’s inspection when you sell.

We apply for the permit with your city or county, complete the work to code and call for inspections. The inspector checks the wiring before walls close and again at the end. Once it passes, the permit is closed.

Very little in most homes. We use the attic, closets and existing openings, and cut small, clean access holes only where a wire cannot be pulled another way. Those patch easily.

Not always. Listed aluminum to copper connectors on every connection are an accepted repair. Replacing the wire with copper removes the issue for good. We explain both and let you choose.

The size of the home, how much wire is replaced, the construction, access through the attic and whether the panel needs work. We do not guess from a phone call. We inspect first, and the written estimate that follows costs you nothing.

Still have a question? Call (727) 258-3346 or email contact@bluefinpowersolutions.com.

Get a Free Estimate

Prefer to talk?
(727) 258-3346

Tell us what you need. We call back Monday to Friday, 8 AM to 6 PM.

Menu